首頁 > 產品一覽 > 光學測試設備 > Beam Diagnostic > Beam Profiler - Beamage 3.0
 

Beam Profiler - Beamage 3.0

USB 3.0 for the Fastest Transfer Rates
Up to 10X faster than regular USB 2.0 connections. (also USB 2.0 compatible)

High Resolution
2.2 MPixels resolution gives accurate profile measurements on very small beams.

Large Area Sensor
The 11.3 x 6.0 mm sensor allows to measure very large beams.

ISO Compliant
D4σ Definition of Diameter, Centroid, Ellipticity and Orientation are ISO 11146:2004 and 11146:2005 compliant.

Intuitive Software Interface
Easy to navigate interface, with many display and control features:
˙2D, 3D and XY Displays
˙Background Subtraction Function
˙Unique "Animate" Function
˙Gaussian Fit
˙Semi-Log Graph

External Trigger
To synchronize the camera with a pulsed laser.

Low-Cost
The most affordable, large size camera-based beam profiler on the market.
  • 型號
  • 產品概述
  • 庫存
  • 詢價數量
  • 詢價車
Beamage 3.0

Beam Profiling Camera.CMOS sensor: 2.2 MPixels, 2048 x 1088, 5.5 um pixels.ISO Calculations.

  •  Sensor Technology  CMOS
     Effective Aperture  11.3 x 6.0 mm

    Measurement Capability

     Wavelength Range  350 - 1150 nm
     Pixel Count  2.2 MPixels.
     H x V  2048 x 1088
     Pixel Dimension  5.5 x 5.5 μm
     Minimum Measurable Beam  ~55 μm
     Shutter Type  Global
     Frame Rate (at 1 MPixels)  10 fps
     RMS Noise  1000:1 (60 dB)
     ADC Level (User Setable)  12 bit (default) / 10 bit (option)

    Damage Thresholds (With ND4 filter)

     Maximum Average Power  1 W
     Saturation Level (1064 nm)  CW: 10 W/cm2 ; Pulsed: 300 μJ/cm2

加入
STAND-D-233

stands

  • Stand with 2 x 3in Base, 3in Cylinder, Delrin Post, ¼-20 & 8-32.

加入
VA-0-93

Beam splitters and Attenuators

  • Variable Attenuator, 93 dB optical dynamic range. Maximum: 1 W/cm2, 100 mJ/cm2.

加入
ND0.5

Stackale ND Filters

  • ND 0.5 filter in C-mount threaded stackable holder

加入
ND1.0

Stackale ND Filters

  • ND 1.0 filter in C-mount threaded stackable holder

加入
ND2.0

Stackale ND Filters

  • ND 2.0 filter in C-mount threaded stackable holder

加入
ND3.0

Stackale ND Filters

  • ND 3.0 filter in C-mount threaded stackable holder

加入
ND4.0

Stackale ND Filters

  • ND 4.0 filter in C-mount threaded stackable holder

加入
ND5.0

Stackale ND Filters

  • ND 5.0 filter in C-mount threaded stackable holder

加入
UG11-UV

Stackale ND Filters

  • UV transmitting 'Black Glass' filter. FWHM: 280 to 370 nm; T = 10% 280 to 370 nm

加入
ND-H

Stackale ND Filters

  • ND Filter Holder for 7/8in (22 mm) diameter filters. Holds filter at an angle of 3 degrees.

加入
NDSET-5

Set of 5 ND filters

  • Set of 5 ND filters in C-Mount holders: ND1.0, ND2.0, ND3.0, ND4.0, ND5.0

加入
NDSET-3

Set of 3 ND filters

  • Set of 3 ND filters in C-Mount holders: ND1.0, ND2.0, ND3.0

加入
BSC-350

Beam Splitter Cube

  • Beam Splitter Cube, 3% to 10% (polarization dependent). For 350 - 2200 nm.

加入
BSC-190

UV Beam Splitter Cube

  • UV Beam Splitter Cube, 3% to 10% (polarization dependent). For 190 - 2200 nm.

加入
PEL-1450

Pelican Carrying Case

  • Pelican Carrying Case (Model 1450). 15 x 11 x 6 in. 1 Monitor / 2 Heads / Stands, Power Supplies, Manuals.

加入
PEL-1500

Pelican Carrying Case

  • Pelican Carrying Case (Model 1500). 17 x 12 x 7 in. 2 Monitor / 2 Heads / Stands, Power Supplies, Manuals.

加入
PEL-1550

Pelican Carrying Case

  • Pelican Carrying Case (Model 1550). 19 x 15 x 8 in. 1 Monitor / 1 Large High Power Head / 2 Standard UP or QE Series Heads / Stands, Power Supplies, Manuals.

加入

SUBTRACT BACKGROUND
The background subtraction function is a necessary tool to have an accurate measurement and to abide
by the ISO-11146-3:2004 standards. By taking 10 images and averaging them pixel by pixel to compute the average background map, contamination of all images can be avoided with the help of environment noise subtraction.

ANIMATE
Give life to your measures with the animate function. With as much as 32 frame images temporarily saved in the buffer, simply pressing the animation button will create a movie with any display (2D, 3D and XY). This allows to visualize the beam while working offline and have a recalculation process if the beam diameter definition or crosshair parameters are changed.

FILTER
Filter out the noise in your beam profile by using this spatial filter function. This tool is great for low quality lasers or low level signals.

NORMALIZE
The normalize function spreads the intensity over the full range (0% to 100%). This is especially useful with low level signals or to enhance the variations in the beam.

TRIGGER
For the case of pulsed laser sources, the trigger function will be useful to synchronize the system’s capture rate with the source’s repetition rate, especially when this one is low (<16 Hz). To be achieved, a TTL (0-5 V) or other (1.1-24 V) trigger signal can be connected to the Beamage 3.0 camera via a BNC or SMA plug.

IMAGE AVERAGING
The image averaging function uses a temporal filter to provide the possibility to take 2, 5 or as much as 10 images of the beam to create a single timeaveraged image with them. This process will smooth the
beam fluctuations that can occur over time when working with unstable laser sources.

ACTIVE AREA (ROI)
Increase the data transfer rate by reducing the area of the sensor that is scanned. This tool is perfect for
small beams that don't need the full sensor area.

PIXEL ADDRESSING
Increase the data tranfer rate by using larger pixels or by reducing the number of pixels. This is great for large beams that don't need the full resolution.

Specifications

 Sensor Technology  CMOS
 Effective Aperture  11.3 x 6.0 mm

Measurement Capability

 Wavelength Range  350 - 1150 nm
 Pixel Count  2.2 MPixels.
 H x V  2048 x 1088
 Pixel Dimension  5.5 x 5.5 μm
 Minimum Measurable Beam  ~55 μm
 Shutter Type  Global
 Frame Rate (at 1 MPixels)  10 fps
 RMS Noise  1000:1 (60 dB)
 ADC Level (User Setable)  12 bit (default) / 10 bit (option)

Damage Thresholds (With ND4 filter)

 Maximum Average Power  1 W
 Saturation Level (1064 nm)  CW: 10 W/cm2 ; Pulsed: 300 μJ/cm2

Software

 Displays  2D, 3D and XY
 Display Features

 2D: Print Screen, Reset View, Show/Hide Beam
 Diameter
 3D: Print Screen, Reset View, Top View
 XY: Save Data, Zoom, Gaussian Fit, Semi-Log,
 Show/Hide Cursor, Show/Hide FWHM,
 Show/Hide 1/e2

 Beam Diameter Definitions  D4σ (ISO compliant)
 1/e2 along crosshairs (13.5%)
 FWHM along crosshairs (50%)
 86% effective diameter (D86)
 Buffer Controls  Open File, Save Current Data, Save All Data,
 Previous/Next Image, Clear Buffer, Animate
 Printing and Reports  Full Report in Print Ready Format (2D, 3D, XY, Measures,
 Parameters)
 Print Screen in BMP format (2D and 3D)

Physical Characteristics

 Sensor Size  11.3 x 6.0 mm
 Sensor Area

 0.67 cm2

 Dimensions (not including filter)  61H x 81.1W x 19.7D mm
 Weight (head only)  139 g

INTUITIVE SOFTWARE INTERFACE

MAIN CONTROLS
The top portion of the software is in a ribbon format and includes all the main controls. These are grouped by family, including capture controls, file controls, buffer controls and data computations such as a very useful spatial filter and a normalizing function.

DISPLAYS
The left-hand side of the software is the display panel. 3 displays are available: 3D, 2D and XY (cross-sectional graphs along the crosshairs). The various displays are chosen using the corresponding icons at the bottom of the panel. Convenient Print Screen controls are located the 2D and 3D displays and allow the user to save an image of the current view in BMP format.

HOME and SETUP TABS
The right-hand side of the software contains the Home and Setup tabs. The Home tab allows the user to
select the type of measurements performed (like 4-sigma and FWHM). It also shows the resulting measures of the beam. The Setup tab contains all the measurement parameters, like Exposure Time, Image Orientation, Averaging, Active Area definition (ROI) and more.

產品說明書

檔案大小

下載

Beamage 3.0 產品型錄
1643 KB